home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
QRZ! Ham Radio 4
/
QRZ Ham Radio Callsign Database - Volume 4.iso
/
digests
/
homebrew
/
940302.txt
< prev
next >
Wrap
Internet Message Format
|
1994-11-13
|
9KB
Date: Thu, 13 Oct 94 04:30:33 PDT
From: Ham-Homebrew Mailing List and Newsgroup <ham-homebrew@ucsd.edu>
Errors-To: Ham-Homebrew-Errors@UCSD.Edu
Reply-To: Ham-Homebrew@UCSD.Edu
Precedence: List
Subject: Ham-Homebrew Digest V94 #302
To: Ham-Homebrew
Ham-Homebrew Digest Thu, 13 Oct 94 Volume 94 : Issue 302
Today's Topics:
coffee-can notch filters?
help with 12v supply regulation
How to design VCO?
Lead-Acid Charger
pin diode attenuators & AGC
Suggestions on Lemon Powered QRP rig
Tube/Valve Amp parts
Send Replies or notes for publication to: <Ham-Homebrew@UCSD.Edu>
Send subscription requests to: <Ham-Homebrew-REQUEST@UCSD.Edu>
Problems you can't solve otherwise to brian@ucsd.edu.
Archives of past issues of the Ham-Homebrew Digest are available
(by FTP only) from UCSD.Edu in directory "mailarchives/ham-homebrew".
We trust that readers are intelligent enough to realize that all text
herein consists of personal comments and does not represent the official
policies or positions of any party. Your mileage may vary. So there.
----------------------------------------------------------------------
Date: Wed, 12 Oct 1994 13:31:06 GMT
From: zlau@arrl.org (Zack Lau (KH6CP))
Subject: coffee-can notch filters?
Bill Turner W7LZP (wrt@eskimo.com) wrote:
:
: The coffee-can type filters work pretty well for receiving, but they're
: too lossy to use for transmitting. A friend of mine brought a six meter
: version into work the other day and we hooked it up to a $30k HP
: impedance analyzer just to see what it was REALLY doing. It had a nice
: sharp peak at 50 MHz just as advertised, but you should have seen the
: look on his face when he realized it had a 3db insertion loss. This
: means that half the power through it was lost as heat. Good thing he
: wasn't running a KW - would have kept the room nice and warm!
The loss for a given filter topology is a function of the ratio between
the unloaded and loaded Qs. Thus, you can reduce the loss to acceptable
levels by increasing the bandwidth of a bandpass filter (I assume by a
"sharp peak" you are talking about a BPF). This is why inductor/capacitor
input circuits can sometimes do as well as expensive cavity input circuits
on preamps--sometimes you can lower the loaded Q enough to compensate for
the lossier parts while still getting the required impedance transformation.
: The problem of course is that there is a very large amount of
: circulating tank current in the device. Had it been silver-plated, it
: probably would have been ok. If you still want to try one for six
: meters, email me and I'll get you the dimensions. For other bands you
: could scale it up or down, but at higher freqs, the loss will be even
: higher due to increasd skin effect.
Silver plating tends to be over-rated. To reduce the loss from 3 dB to
1 dB (still a lot of heat at the kW level), you would have to improve
the unloaded Q by by a factor of 2.7. I doubt that silver plating would
improve a tin plated can that much. My guess is that you would be
lucky to get a 20% improvement in Q. Of course, silver plated cavities
look a lot nicer than unplated copper ones--a big factor if you are
trying so *sell* something.
--
Zack Lau KH6CP/1 2 way QRP WAS
8 States on 10 GHz
Internet: zlau@arrl.org 10 grids on 2304 MHz
------------------------------
Date: 12 Oct 1994 18:21:50 GMT
From: greendot@lamar.ColoState.EDU (Robert Taylor)
Subject: help with 12v supply regulation
Hello I am building a 12v regulated power supply but i need help
regulating it! I don't know wich transistor's to use or exactly
how they should go. The transformer is a 12 amp non center tap.
could someone please mail about what the suitable transistors would
be and how to controll them!
Thanks a bunch
Robert
------------------------------
Date: 13 Oct 1994 07:48:00 GMT
From: fredkuo@PROBLEM_WITH_INEWS_DOMAIN_FILE.UCSD.EDU (m330_fredkuo)
Subject: How to design VCO?
I have a question on VCO design : the resistor and
capacitor of voltage control input, normally for filtering
out the noise ,seems to change the PLL characteristics.
for example, a vc input as follows
R = 4.7k
VC I/p>---|---|\|\|\|\|-------> to varactors
|
___
___ C = 50 uf
|
|
|
---- GND
The big capacitor 5uf is directly parallel connects with the
loop filter of PLL. Should I take this capacitor as a part of the
PLL loop filter? And, how can I design a VCO that will not affect
the PLL performance ?
fred Kuo | BV3DH
PO BOX 9-99, Hsinchu, Taiwan
------------------------------
Date: Wed, 12 Oct 1994 01:13:24 GMT
From: tkreyche@zdlabs.ziff.com (Tom Kreyche)
Subject: Lead-Acid Charger
In article <371ejt$8c5@snoopy.jh.org>, ss@JH.Org (Steve Steinberg) wrote:
> I want to build a battery charger for deep-cycle (marine) batteries......
I called Unitrode at 603-424-2410 and received a copy of their "Product and
Applications Handbook 1993-1994." Besides the product infomation on their
"Sealed Lead-Acid Battery Charger" chip there is an extensive app note
"Improved Charging Methods for Lead-Acid Batteries Using the UC3906." These
two docs tell more than you'll need to know about the subject. The UC3906
is the chip used in the charger circuit in the 1994 ARRL handbook.
-tk
------------------------------
Date: 12 Oct 1994 20:14:37 GMT
From: kirkland@bgtys22.bnr.ca (Bill Kirkland)
Subject: pin diode attenuators & AGC
Does anyone have any suggestions on building pin diode
attentuators @ 9 MHz. My interest is in building an
IF stage with pin diode attenuators for AGC and I have been
thinking about using the MAR or MAV series of amplifiers for
the amplifier chain. I know that this might be over kill when
you could use MC1350's or dual gate mosfets but the MC1350's are
only rated 0 - 70 deg C and dual gate mosfets seem to be extremely
hard to obtain and once a source is found relatively expensive.
What else is done for IF amps and AGC?
( I also know about the Plessey series of devices - they too are not cheap
Does anyone know of a source for Plessay in the states that is willing
to supply in the usual small quantities)
Bill Kirkland
p.s. I am presently playing around with the high performance AGC circuit
described in Solid State Design for the Radio Amateur and in
countless ARRL handbooks that uses the now unattainable Motorola I.C.
modified for the MC1350.
------------------------------
Date: 12 Oct 1994 12:42:51 GMT
From: clarke@acme.ist.ucf.edu (Thomas Clarke)
Subject: Suggestions on Lemon Powered QRP rig
In article <37ejpf$iqi@info2.rus.uni-stuttgart.de>
moritz@ipers1.e-technik.uni-stuttgart.de () writes:
> I have to dissapoint you in saying that there is not such a thing as lemmon
> power. In the system you want to demonstrate the power comes from the
> electrodes dissolving in the poor fruit, which is being abused as electro-
> lyte.
> Ever wondered why Nicads are not called potassium-hydroxides?
> These "lemmon powered" demos only contribute to confusion
> and should be dropped quietly.
Apparently non-metals are getting a bad rap in the battery world.
For the sake of political correctness, perhaps we should rename
NiCads: transition metal/alkaline hydroxide power units,
dry cells: transition metal/alkaline chloride power units,
lead acid: heavy metal/inorganic acid power units, and ...
lemon power: transition metal/organic acid power units.
Tom Clarke
------------------------------
Date: Wed, 12 Oct 1994 13:36:11 GMT
From: asj@dsbc.icl.co.uk (Adrian Jefferies)
Subject: Tube/Valve Amp parts
Hi
The following was previously posted to rec.music.makers.guitar.
I am in the process of performing a service on my mid 60's Fender Princeton
guitar amplifier.
I have been having trouble locating sources for the valves [tubes] &
high value (450V) electrolytic capacitors. Can anyone recommend places to
get these parts, prefereably in the UK? I have got the parts I need
on order, but with hindsight I should have spent a bit more time
calling around. I'll be using new Fender valves - I wont admit to how
much these things have cost me .... I was in hurry ....
I dont read this newsgroup, so any email responses gratefully received.
I'll collate & repost any pertinent information.
Regards, Adrian
asj@dsbc.icl.co.uk
------------------------------
End of Ham-Homebrew Digest V94 #302
******************************